PLCs Y CONTROLADORES · OMRON

2-AXLE MOTION CONTROLLER WITH G-LANGUAGE FOR CONTROL FROM CS1 PLC'S, ANALOG OUT, PLEASE NOTE: THREE COUNTS AS SPECIAL I / O MODULES

4-AXLE MOTION CONTROLLER WITH G-LANGUAGE FOR CONTROL FROM CS1 PLC'S, ANALOG OUT, PLEASE NOTE: FIVE COUNTS AS SPECIAL I / O MODULES

4-AXLE MOTION CONTROLLER WITH G-LANGUAGE FOR CONTROL FROM CS1 PLC'S, ANALOG OUT, PLEASE NOTE: FIVE COUNTS AS SPECIAL I / O MODULES

ADVANCED 30-AXLE MODULE MOTION FOR CS1, INCL. PROGRAMMING SOFTWARE

DC INPUT/ TRANSISTOR OUTPUT UNIT, INPUT: 32 POINTS, OUTPUT: 32 POINTS, TRANSISTOR OUTPUT (SINK), INPUT VOLTAGE DC24V

32 IN NPN / PNP, 24 VDC SWITCH ADJUSTABLE DELAY AND 32 FROM PNP, 12-24 VDC / 0.3 A 40 POINT WITH FUJITSU CONNECTOR, SHORT CIRCUIT VAST

DC INPUT/ TRANSISTOR OUTPUT UNIT, INPUT: 48 POINTS, OUTPUT: 48 POINTS, TRANSISTOR OUTPUT (SINK), INPUT VOLTAGE DC24V

48 IN NPN / PNP, 24 VDC AND 48 FROM PNP, 12-24 VDC / 0.1 A 56 POINT WITH FUJITSU CONNECTOR

CS SERIES POSITION CONTROL UNIT, 1 AXES CONTROL, CONTROLLED DRIVER: PULSE-TRAIN INPUT-TYPE SERVO DRIVE OR STEPPING MOTOR DRIVER, CONTROL UNITS: PULSE, CONTROL SYSTEM: OPEN-LOOP CONTROL BY PULSE TRAIN OUTPUT (OPEN COLLECTOR OUTPUT), OPERATING POWER SU

CS SERIES POSITION CONTROL UNIT, 1 AXES CONTROL, CONTROLLED DRIVER: PULSE-TRAIN INPUT-TYPE SERVO DRIVE OR STEPPING MOTOR DRIVER, CONTROL UNITS: PULSE, CONTROL SYSTEM: OPEN-LOOP CONTROL BY PULSE TRAIN OUTPUT (LINE DRIVER OUTPUT), OPERATING POWER SUPPL

CS SERIES POSITION CONTROL UNIT, 2 AXES CONTROL, CONTROLLED DRIVER: PULSE-TRAIN INPUT-TYPE SERVO DRIVE OR STEPPING MOTOR DRIVER, CONTROL UNITS: PULSE, CONTROL SYSTEM: OPEN-LOOP CONTROL BY PULSE TRAIN OUTPUT (OPEN COLLECTOR OUTPUT), OPERATING POWER SU

CS SERIES POSITION CONTROL UNIT, 2 AXES CONTROL, CONTROLLED DRIVER: PULSE-TRAIN INPUT-TYPE SERVO DRIVE OR STEPPING MOTOR DRIVER, CONTROL UNITS: PULSE, CONTROL SYSTEM: OPEN-LOOP CONTROL BY PULSE TRAIN OUTPUT (LINE DRIVER OUTPUT), OPERATING POWER SUPPL

CS SERIES POSITION CONTROL UNIT, 4 AXES CONTROL, CONTROLLED DRIVER: PULSE-TRAIN INPUT-TYPE SERVO DRIVE OR STEPPING MOTOR DRIVER, CONTROL UNITS: PULSE, CONTROL SYSTEM: OPEN-LOOP CONTROL BY PULSE TRAIN OUTPUT (OPEN COLLECTOR OUTPUT), OPERATING POWER SU

CS SERIES POSITION CONTROL UNIT, 4 AXES CONTROL, CONTROLLED DRIVER: PULSE-TRAIN INPUT-TYPE SERVO DRIVE OR STEPPING MOTOR DRIVER, CONTROL UNITS: PULSE, CONTROL SYSTEM: OPEN-LOOP CONTROL BY PULSE TRAIN OUTPUT (LINE DRIVER OUTPUT), OPERATING POWER SUPPL

CS SERIES POSITION CONTROL UNIT, WITH MECHATROLINK-II INTERFACE, 16 AXES CONTROL, CONTROLLED DRIVER: G5-SERIES, G-SERIES SERVO DRIVES (BUILT-IN MECHATROLINK-II COMMUNICATIONS), CONTROL UNITS: MM, INCH, DEG, PULSE, CONTROL SYSTEM: MECHATROLINK-II POSI

TRIAC OUTPUT UNIT, OUTPUT: , TRIAC OUTPUT

TRANSISTOR OUTPUT UNIT, OUTPUT: 16 POINTS, TRANSISTOR OUTPUT (SOURCE)

32 OFF, NPN TRANSISTOR, 12-24 VDC, 0.5 A 40 POINT WITH CONNECTOR FUJITSU

32 OFF, PNP TRANSISTOR, 24 VDC, 0.5 A 40 WITH POINT FUJITSU CONNECTOR, SHORT-CIRCUIT PROOF

64 OFF TRANSISTOR NPN, 12-24 VDC, 0.3 A WITH 2 40 FUJITSU POINT CONNECTOR

64 OFF PNP, 24 VDC / 0.3 A WITH 2 40 POINT FUJITSU CONNECTOR, SHORT-CIRCUIT PROOF

TRANSISTOR OUTPUT UNIT, OUTPUT: 96 POINTS, TRANSISTOR OUTPUT (SINK)

TRANSISTOR OUTPUT UNIT, OUTPUT: 96 POINTS, TRANSISTOR OUTPUT (SOURCE)

ISOLATED-TYPE DIRECT CURRENT INPUT UNIT, INPUT 4 POINTS , INPUT SIGNAL00 TO 10 V/-10 TO 10 V/0 TO 5 V/-5 TO 5 V/1 TO 5 V/0 TO 1.25 V/-1.25 TO 1.25V/+- 10 V USER-SET RANGE (SPECIFIED RANGE WITHIN - 10.000 V TO 10.000 V)/4 TO 20 MA/0 TO 20 MA, 1/64000,